Wd40 shower diverter

Wd40 shower diverter DEFAULT

How do you fix a shower tub diverter?

Why does my shower diverter not work? If, after you trigger your shower diverter, water continues to leak out of the bathtub spout rather than the showerhead, the shower diverter is not working properly. This could mean that the inner rubber stopper isn&#;t creating a good seal to fully block and redirect the flow of water, or it could be another problem.

Why is my shower diverter stuck? Sometimes, the diverter gate gets stuck. When you try to turn it or pull it up, it refuses to budge or makes squeaky, grating noises. If you do manage to pull it up, it may stick at the top and refuse to push back down. This is probably due to accumulated dirt, grease, and limescale.

Can&#;t get my tub spout off? The first step is to cut through any caulk between the spout and wall. Then grip the spout near the wall with a inch pipe wrench and try again with a little more gusto. Push counter-clockwise, using steady pressure. If that approach doesn&#;t work, you&#;ll need to cut off the spout with a hacksaw.

How do you fix a shower tub diverter? &#; Related Questions

How much does it cost to replace a shower diverter?

Depending on the severity of the leak, it can cost between $ and $ to fix it.

Can you use wd40 on shower diverter?

WD is great for the bathroom, too

Check out the WD EZ-Reach, perfect for loosening up a sticking tub spout diverter!

Can a shower diverter cause a leak?

When a diverter valve is working properly, water only flows out of either the tub spout or the showerhead. However, diverters very often leak significantly, allowing water to flow out of the tub spout even when in shower mode, as shown in Figure 3.

Where is the diverter valve located?

Single-Valve Shower Diverter

This diverter valve, also known as a tee diverter, is located on the end of the tub spout (see photo above). Activating it requires simply pulling up on the diverter, which then sends water to the showerhead.

Do you have to turn off water to change shower diverter?

If you&#;re only working on the diverter, you don&#;t need to turn off the water supply to the faucet. While working, place a cloth over the tub drain to prevent any dropped screws from going down the drain. Some showers use a diverter built into the tub spout activated by lifting a button on the spout.

How long does a shower diverter valve last?

The valves are easy to move against pressure. Control the volume from off to full on by leaving them set to the same temperature. The system costs about $30 to replace, but they last for 20 to 30 years.

Can a bad shower diverter cause low water pressure?

a defective or stuck bathtub spout diverter can cause low shower pressure. This is because your diverter is unable to divert water from your tub spout up to your shower head effectively. To fix this problem, call a plumber to fix/replace your spout diverter.

Can a shower diverter go bad?

It does exactly what it&#;s named for: it diverts (changes direction) water from one place to another. The only problem with shower diverter valves is they don&#;t last forever, and there are many times—like all of the other components of your home—when they fail from old age and normal wear and tear.

How do you free a stuck diverter valve?

After you remove the lid of the boiler, you have to locate the diverter valve mechanism. Run tap water on hot and observe the diverter valve. If you run hot water, the valve is supposed to close in order to divert it to the tap, meaning it should move. If you see no movement, then it&#;s stuck.

Why does my diverter valve keep failing?

Diverter valves can become damaged or stuck. This is because they&#;re a moving part and can be oscillating between being open or closed many times a day. However, they are fixable. If you have no hot water, try turning the heating on.

How does shower tub diverter work?

This valve is what allows you to choose between filling your bathtub and taking a shower. In short, it diverts water up into the showerhead instead of coming out of the tub spout. The user typically adjusts the faucet to the preferred water temperature before activating the diverter and sending water to the showerhead.

How much does it cost to replace a tub spout?

Install a Bathtub Spout: national average cost

The national average materials cost to install a bathtub spout is $ per spout, with a range between $ to $ The total price for labor and materials per spout is $, coming in between $ to $

How do you remove a stubborn tub spout?

Use pliers or a pipe wrench to grip the spout and turn it clockwise to release. Some screw-on tub spouts may be tighter because of internal threading or caulk that was applied upon install. If yours has caulk, carefully scrape any excess from around the base of the spout before you try twisting it.

How much does a plumber charge to install a shower?

Cost to Install Shower Plumbing

Hiring a plumber costs $ to $1, per fixture, depending on the size of the project. If you have to run a new drain line, you may pay $1, to $7, It can be easy to forget these possible expenses, particularly if you&#;re putting a shower in the same place.

Is a diverter valve expensive?

You&#;ll come across various models, many of which will provide either heating or hot water, however, a mid-position diverter valve allows you to have heating, hot water and both. They tend to be more expensive but being able to use hot water and keep your radiators warming up is well worth the extra investment.

Why put WD up your faucet?

Although leaky faucets may seem like a small issue, it should never be ignored as all those drops of water add up, and if it&#;s not addressed properly, could turn into a larger problem. Spray a little WD Multi-Use Product to loosen the screw, and unscrew the faucet handle from the stem.

Why is my bathtub leaking underneath?

Leaking drains are a likely cause of water that seeps from underneath your bathtub. This could be a leak coming from under the drain, which would require the help of a plumber to set right. However, a leaking tub drain could also be caused by a failing seal in the vicinity of the drain assembly.

Why does water comes out of shower head when filling tub?

Most likely the problem is just the diverter on your tub spout, it&#;s probably not opening all the way, which allows some back pressure to build up in the pipe that eventually gets back up to the shower head. It could also be corrosion inside of the pipe that is having the same effect.

Do I need a diverter valve?

Shower diverter valves can be a pretty confusing part of the shower build process. Without one, you&#;ll have no ability to redirect the flow of water. Even if you have a simple setup with just a tub faucet and a showerhead, you&#;ll need a diverter valve to switch between them.

When should a shower valve be replaced?

The first issue to look for is if there are any leaks in the valve when you turn on the water. If there are drips, that&#;s a good indication that you should think about replacing the valve. Because, not only are you wasting water, but water that leaks behind the wall can cause rot as well as mold and mildew growth.

Does water pressure affect shower diverter?

Diverter valve

If this valve, sometimes in the shape of a switch or knob, becomes broken then the water pressure may drop for the shower head. To solve this problem, a plumber may repair or replace the diverter valve. They may also repair or replace the seal that is allowing the water to escape.

Sours: https://cementanswers.com/how-do-you-fix-a-shower-tub-diverter/

Audiology & Hearing Aids in Bel Air, MD

State-of-the-art diagnosis and treatment

Even the best hearing aids are only as good as the level of service that accompany them. At Bay Area Audiology, we strive to offer the highest level of personalized, caring service to each and every one of our clients. We use advanced techniques to determine the root causes of your hearing difficulties and offer a customized approach in a friendly and welcoming atmosphere so that you will feel comfortable navigating the unknowns of hearing loss.

Bay Area Audiology provides comprehensive hearing evaluations, hearing services and hearing aids to clients in Bel Air, Fallston, Forest Hill, Emmorton, Churchville, Jarrettsville, and throughout Harford and Baltimore Counties. We are an independent and locally owned audiology practice, with no ties or influence from manufacturer sales incentives. This means we can remain unbiased in our recommendations and simply provide you with the very best hearing aid solution for your unique hearing loss and lifestyle needs.

If you feel that you or a loved one is experiencing hearing loss, give us a call at () to take the first step toward regaining control over your hearing.

Learn More

Sours: https://belairhearingaids.com/wp-content/tgyuxr2/cc53bd-tub-spout-diverter-not-working
  1. Straight messy hairstyles
  2. Red cross pocatello
  3. Fairlife protein review

How To Fix A Shower Diverter? The Most Thorough Guide of

Is it challenging to learn how to fix a shower diverter? Frankly speaking, it is not, even when you don’t know anything about plumbing. The shower diverter is an amazing device, but over time, it needs a little check-up.

With this post, I guarantee that you will succeed on the first attempt. Not only will you cut corners, but you will also learn to do a job that impresses your partner. He or she will be very proud of you!

Table of Contents

In Short, How Can You Repair A Shower Diverter?

First and foremost, you will identify what type of spout and diverter you are using. The repair procedure will be carried out in differing ways depending on which part is faulty.

  • Loosen the diverter with cooking spray or WD
  • Clean or soak the spout in a vinegar mixture or with a lemon wedge

If the cleaning solution does not bear fruit, you will need to replace the diverter or/and the spout.

  • Replace the diverter (the tee, the two-valve, and the three-valve)
  • Replace the whole spout

First, you will get to know some basic information about your shower diverter. Let’s go!

Related Posts:

What Is A Shower Diverter, And What Does It Do?

A shower diverter, sometimes called a diverter valve, is a valve that allows you to switch the water stream between different outputs or use two of them simultaneously without having to install a separate water supply pipe.

It comes in various types, but the most popular is undeniably a small metal tab located on the tub spout. The diverter valve can also be the middle faucet or a button depending on the number of outlets.

Overall, it does an incredible job diverting the water from the tub to the showerhead and vice versa. Not only that, you can control the water temperature from the tub faucet first without burning yourself, and you’ll be glad to know that most diverters are easy to install.

How Many Types Of Shower Diverters Are There?

The answer will vary depending on how you categorize them. Let’s dive deeper into each type of shower diverter and learn their differences as well as their pros and cons.

Classification According To The Number Of Outlet Points

A shower diverter can have up to four water outputs. With its flexibility, your shower time is sure to be unforgettable.

Tee Diverter

Also known as a single-valve diverter, the tee diverter is the most basic type and the most popular. It is located inside the faucet and controlled by a small tab on the spout. When pulled up, the water stream is diverted from the tub faucet to the showerhead.

Two-Valve Diverter

This type of diverter is normally accompanied by a single-handle faucet mounted on the wall. The water can be diverted easily to the tub faucet and the showerhead by the lever.

Meanwhile, the larger handle controls the temperature, although some types feature two separate knobs for the hot and cold water.

Three-Valve Diverter

The three-valve diverter is as commonly used as the T-diverter, yet the installation is more complicated. In short, the water can be diverted between three different outputs, for instance, the tub faucet, the showerhead, and the handheld.

And here’s the best part: you can choose to direct the water flow to one or two outlets simultaneously. It is usually controlled by a lever, sometimes a knob or a button as well, with the other two matching parts used to control the water temperature.

Four-Valve Diverter

As the name implies, the water can be sent to four different outputs, and two of them can run at once. For example, you can enjoy a hot bath while using the showerhead or the handheld. The tricky part is that the outputs must be lined up correctly in order to do so.

Classification According To The Design

A shower diverter can be exposed or hidden underneath the wall. What’s your pick?

Concealed Diverter

This is the ideal choice if you care about the curb appeal. The ugly pipework is hidden behind the wall, so the only visible part is the control plate with handles or buttons.

Moreover, this type of shower valve offers a wide range of options, from gold to chrome finish, rectangular to oval shape, and so on. Of course, with such intricate designs, you will have to pay a little extra to bring one home.

Exposed Diverter

The exposed shower diverter is usually a horizontal bar mounted to the wall and houses the working parts. Overall, the design is not neat, and since there are fewer options, this type of diverter usually does not cost you much.

Classification According To The Function

The next two shower valves will ensure that you are safe from being scaled and your shower experience is not ruined. Here’s how they do it.

Manual Valve

The manual valve is simple and easy to use. By pulling a lever up and down, you can set the water flow and temperature with ease. There’s a significant drawback, though, and it can be quite threatening sometimes.

If someone else in the house opens the tap water or flushes the toilet as you are enjoying the shower, the temperature will suddenly increase or decrease without warning. And yes, no one likes it when this happens.

Thermostatic Valve

Have you ever experienced the water abruptly getting too hot when someone else in your family turns on the faucet? That can be irritating, sometimes dangerous, and the thermostatic valve right here is your ultimate solution.

It frequently comes in two options, two and three handles, and can be controlled manually or digitally with a remote. With such fantastic features, the price is not low &#; but it’s a worthy investment, especially if you have children.

Now, let’s move on to some issues that you usually face while using the shower diverter.

What Are Some Common Problems With Shower Diverters?

Over time, the chances are that your shower diverter will not work as effectively as before, spoiling the bathtime fun. I have rounded up some common problems below, followed by the culprit and the solution.

Faulty Diverter

Over time, the diverter or some parts of it will likely be damaged. For instance, the gasket will wear out or the gate will slip out of where it should be, leading to blockage.

In addition, it is sometimes stuck, and it takes a great effort to pull it up or push it down. Even if you manage to do it, there’s this squeaky noise indicating that something’s off. The solution is to clean it or replace it with a new one.

Unknown Sound

At times, there’s this strange, high-pitched sound interrupting your singing as you are taking a shower. If you have ever asked yourself what it is, look no further &#; it’s your shower diverter telling you that it isn’t doing well.

Before finding its way to you, the water has to go through a small hole. Sometimes, due to the mineral deposits, the hole is clogged and eventually leads to blockage, resulting in a hissing or whistling sound as the water attempts to pass through the hole.

In this situation, it’s your job to clean either the showerhead pipe or the diverter.

Problems Concerning The Water Flow And Pressure

Provided that your shower diverter does not function properly, such as decreased water pressure, uneven flow, or leaks, there’s a high possibility that it has been stuck or malfunctioned. Sometimes, the causes are beyond the diverter itself.

A clogged showerhead can be the culprit, but it can also be caused by a worn-out mixing valve, a faulty water heater, or corroded pipes. Although most of these issues sound rather complex, you can fix them by cleaning or replacing the spout or the diverter.

Note: A custom shower will be difficult to work on your own, so it’s suggested that you seek professional help instead, especially if your home warranty is still valid. You will be charged a small service fee, but it’s usually reasonable and helps you avoid a huge mess

How Do You Repair The Shower Diverter?

Overall, fixing the shower diverter is not a daunting task, but it will cost you some time. Let me show you how to do it step by step, and illustrations will also be provided to make it clearer for you.

Cleaning The Spout/Diverter

Surprisingly, most of the inconveniences mentioned in the previous section can be easily resolved by cleaning the spout or the diverter. By doing so, all the mineral deposits will be removed thoroughly, giving way to the water stream.

Option 1: Clean The Spout With Vinegar

Cleaning the spout ensures that it is free from all the dirt, grease, and other sediments. Therefore, it’s well-advised that you do this regularly.

Step 1: Pour white vinegar into a plastic bag and dilute it with water if you wish.

Step 2: Wrap the bag around the spout so that the spout submerges completely.

Step 3: Hold the bag in place with a rubber band or a string. Make sure that it’s tightened so that the bag won’t fall.

Step 4: Leave it for days.

Step 5: Remove the bag and give your spout a quick wipe. Check whether the diverter works as it should.

Not only does this simple trick help get rid of the mineral deposits, but it also gives your spout a shiny look without costing you too much. Although other bathroom cleaners work as well, vinegar is a better option since it does zero harm to the environment.

Watch this video to know more:

Watch this video: This trick does wonders in getting rid of the lime on your spout

Option 2: Clean The Spout With A Lemon Half

Lemon is also high in acidity, so it is as effective as vinegar. In fact, you only need a few hours to remove all the limescale from the spout.

Step 1: Remove the center of a lemon half.

Step 2: Press the open lemon half onto the spout’s end.

Step 3: Similar to Option 1, you will need to secure it with a plastic bag and a rubber band.

Credit: The Family Handyman

Step 4: Leave it for a few hours.

Step 5: Scrape off the buildup with a scrubbing pad or an old toothbrush. The spout has been restored to its former glory!

Option 3: Loosen The Diverter

Don’t give up yet if the diverter refuses to obey. Here’s another method with cooking spray that works wonders.

Step 1: Pull and push the diverter by hand so that it loosens a bit.

Step 2: Lubricate the tab with cooking spray or WD

Step 3: Try pulling it up and pushing it down several times until it moves smoothly. Spray more if needed.

Step 4: Wipe the residue off the spout and the diverter. Check if the diverter works now.

Note: If you don’t have a cooking spray or WD, you can use a brush to apply cooking oil and follow the other steps as instructed. Do not use wax or hair spray, as they will damage the metal and plastic parts of your shower.

You’ll be astonished to know that cooking spray can fix a faulty diverter

Watch this video: Spout Repair For Sticky Leaky Shower Tub Spout

Option 4: Soak The Spout In Vinegar

If cleaning the spout is not enough, you will have to bathe the spout. Of course, you will have to remove it first, and here’s how.

Step 1: Turn off the water supply to prevent flooding.

Step 2: You will need to figure out how the spout is attached to the wall in order to remove it. Typically, it has a screw underneath the spout, so all you have to do is unscrew and pull the spout out. If it doesn’t have on, try the following methods:

  • Turn the spout counterclockwise by hand or with a wrench.
  • Pry the spout off with a screwdriver or a palette knife.

Step 3: Remove the dirt and stains with a scrubbing pad or sandpaper.

Step 4: Let the spout submerge in vinegar and water.

Step 5: Leave it for days. Check the spout every day and scrape off the dirt with an old toothbrush.

Step 6: Let it dry and put some Teflon tape on the tip before you reinstall.

Step 7: Put the spout back onto the copper pipe. Power up the water supply and see if everything’s back to normal.

By now, the spout and the diverter should be spotless and working properly. Unfortunately, if there are still leaks or similar problems with the water flow, it’s time to say goodbye to the old shower diverter kit and get a new one.

Replacing The Spout/Diverter

Bad news, if cleaning did not help, it’s time to move on to the final solution: buying a new spout or diverter, sometimes both, from the local hardware store.

Don’t worry; the components don’t cost much, and since you have already saved some money from calling in the plumber to help you with the installation, it’s a win-win.

And by the way, how can you tell which one is to blame: the spout or the diverter? You can inspect the condition and age of both fixings. If you are still unsure, bring them to the hardware store and have someone take a look.

Note: If you have a threaded sprout, make sure that the threads on the new diverter run in the same direction as the old one. Again, if this is confusing, ask someone for assistance.

Option Replace The Tee Diverter (Tub Spout)

In most situations, you only need to replace the valve gate. Largely, most diverters are pretty cheap and straightforward to assemble, so you should be able to do the job without difficulties.

Step 1: Turn off the water supply.

Step 2: Even though you will replace the diverter only, it’s essential to bring the spout to the home improvement store with you as well so that you can find the exact replacement.

The spout can be pulled out in three ways according to how it is attached to the wall as mentioned in steps 2 in Option 3.

Step 3: Stop by your local hardware store and look for a tub spout diverter repair kit that fits the spout. Consult the employees if you are not certain about the model you have chosen.

The kit consists of three components: a stem, which is the thing that you push and pull to divert the water, along with a plastic gate and a diverter gasket. Typically, the instructions are included, but I’ll show you how to do it if there isn’t one.

Step 4: Remove the old components. As you pull the diverter stem out, the old gasket and the gate should come off as well.

Step 5: Insert the new gasket into the plastic gate.

Step 6: Slide the gate with the gasket attached into the underside of the spout.

Step 7: Insert the new stem into the hole. Try pushing it to see if the movement is smooth. If it’s not, you will need to fabricate the plastic gate using sandpaper.

Step 8: Cover the pipe with Teflon tape.

Step 9: Reassemble the spout and make sure that it’s tightened.

Step Turn on the water supply and do a test run. If there are no more leaks, congrats &#; you have done an incredible job!

Note: This guide applies to most tub spout diverters but not all. Some will be assembled slightly differently, so read the instructions carefully before you get into work. Should there be any confusion, you can contact the plumber for help.

Watch this video to know more:

Watch this video: Replacing the new spout diverter has never been this easy

Option Replace Two-Valve And Three-Valve Diverters

Most two-valve and three-valve diverters are controlled by knobs or buttons, sometimes levers. Concerning the latter type, it is commonly used in old bathrooms. However, you can still expect to see it nowadays.

When you work with these types of diverters, you will notice that their piping mechanisms are sort of different. The number of copper pipes you will see corresponds with the number of outlets.

So, how do you know where the valve is? For the two-valve diverter, it will be the one that connects with the temperature dial. For the three-valve diverter, the valve is located on the middle pipe. The replacing process is the same for two types of diverters.

Step 1: Shut off the water supply.

Step 2: Pry the decorative mount off the correct handle.

Step 3: Unscrew and remove the handle. For old handles, it can be a little tricky to get them out. Use a faucet handle puller to help you.

Step 4: Remove the escutcheon.

Step 5: Upon removing, you will see the diverter stem. Continue removing it by loosening the nut. Do it gently as the copper pipes are pretty delicate.

Step 6: Inspect the stem and replace any corroded or worn-out parts, such as the washer.

Step 7: Reassemble by doing everything in reverse. Make sure that everything is fastened to prevent leaking.

Step 8: Turn on the water supply and do a little testing. Does the water run properly now? If so, the repair is done!

You won’t meet any difficulty while repairing the 3-valve shower diverter

Watch this video: How to repair replace 3 way Shower Faucet Diverter

Option 5: Replace The Spout

Don’t sigh &#; replacing the spout is easy as pie. In fact, the steps are already mentioned in the removal procedure of the shower diverter, but I’ll repeat them so that you won’t feel at sea.

Step 1: As usual, you will begin by shutting off the water supply.

Step 2: Remove the spout. Again, refer to step 2 in Option 3 to identify the type of spout you have and the correct way to pull it out.

Step 3: Bring the old spout to the hardware store and get a new one. It should be the same model.

Step 4: The new spout should come with the installation guide, but you don’t need that anyway because it is really simple. Fix it onto the wall according to its design.

Step 5: Reconnect the water supply and test your handy work. You did it!

Watch this video to know more:

Watch this video: Replacing a new tub spout should not waste too much of your time

Keep These Tips On Your Mind For Future Repairs

I know you are already exhausted by now. However, don’t scroll through these brilliant tips and tricks &#; you will regret doing so!

  • Avoid losing anything: immediately upon removing the spout, I suggest covering the drain using duct tape and closing the bathtub drain. The hardware parts are small, and once it falls down the drain, it will be tiring to get them out.
  • Use Teflon tape as you reinstall: it will help create a watertight seal.
  • Tighten everything but not too tight: overtightening will make it troublesome for future maintenance.
  • Clean as you repair: you will want to give the copper pipe a quick clean to remove all the mineral build-up. Vinegar mixed with water is indeed the top-notch choice.
  • Find exact replacements: the new parts should be exactly the same regarding the size and the design. Double-check as you pay; otherwise, you will have to make a return trip to the store.

FAQs

Are you still dazed and confused? If so, check out the next section &#; there are all the explanations for your questions!

I cannot seem to remove the escutcheon. What should I do?

Some escutcheons are caulked to the wall and required to be cut. However, you don’t have to resort to that method as it can damage the stem. Instead, use a strap wrench to get it out.

How do I repair a four-valve shower diverter?

The removal process for this type of shower diverter will be difficult to carry out by yourself. Thus, my advice is to call in a professional plumber.

Water still comes out even when I have shut the water supply off. What should I do?

Let the remaining water run until it stops. After that, you can begin the project.

Can I use pipe dope in place of Teflon tape?

In this case, you can. The pipe dope will do the job as well as Teflon tape.

My tub spout is not cheap, and I don’t want it to scratch. What should I do?

As you are removing and reinstalling it with a wrench, wrap a cloth rag around your spout.

Can a faulty shower diverter cause low water pressure in showerhead?

Yes, it can. Since it’s stuck or broken, water won’t be able to reach the top and therefore cause your showerhead to dribble.

Taking Care Of Your Shower Diverter

That’s it, my friend &#; you have mastered how to fix a shower diverter! There’s no need to wait and waste \ money on the plumber anymore when you can do it on your own. Even when there’s no problem with it, it’s advised that you clean it regularly so that it works well.

Do you have more questions? Or perhaps do you have some brilliant hacks for me and other readers? Share it via the comments below, and I’ll be more than happy to read them. Thanks in advance, and good luck!

Sours: https://www.archfoundation.org/fix-shower-diverter/

If your bathtub has a showerhead,your shower valve redirects water from the showerhead to the tub faucet. When it’s not working, water simultaneously pours from both outlets. It’s easy to fix, so let’s learn how. Shower valves have two parts:

  • A tub spout for filling the tub.
  • A diverter gate – the little knob you twist, turn, or pull to direct your water.

The most common diverter types are:

  • Tee-valve – a single faucet with a pull-up knob
  • Two-valve – one faucet with a knob that turns water hot or cold
  • Three-valve – two faucets, one for hot water and one for cold

Option 1 – Clean your spout

Clean your spout

Sometimes, the diverter gate gets stuck. When you try to turn it or pull it up, it refuses to budge or makes squeaky, grating noises. If you do manage to pull it up, it may stick at the top and refuse to push back down. This is probably due to accumulated dirt, grease, and limescale.

  • Step 1: Mix a batch of white vinegar. It has to be enough to completely cover the spout.
  • Step 2: Pour your vinegar into a plastic bag. If you like, you can mix the vinegar with water.
  • Step 3: Wrap the plastic bag around your spout, submerging the spout.
  • Step 4: Hold the bag in place using a rubber band, string, or shoe-lace.
  • Step 5: Leave the faucet submerged for three or four days, checking it once a day.
  • Step 6: Once the spout looks clean and shiny again, pull the diverter gate to see if it works.

Cleaning your spout with vinegar is good for the environment, because vinegar is organic and non-toxic, unlike harsh bathroom cleaners. It also saves you the cost of buying replacement parts, so it’s a pocket-friendly way to fix your shower leak.

Option 2 – Loosen your diverter with cooking spray

Loosen your diverter with cooking spray

If your diverter gate stays stubborn after your vinegar soak, try using a lubricant to make it work better. Any cooking spray will do, and you probably have some in the kitchen.

  • Step 1: Pull the diverter knob up and down a few times to loosen it.
  • Step 2: Apply some cooking spray to lubricate the knob.
  • Step 3: Try pulling it up and down again. Spray a few more times if you need to.
  • Step 4: Wipe away any excess spray and wash the oil off the bathtub.

Always use cooking spray instead of hair spray or wax. The latter two products have ingredients that could be corrosive and might damage the metal and plastic parts of your shower.

Option 3 – Soak the whole spout

Soak the whole spout

Your vinegar wash will only clean the visible parts of your spout. When you want to stop your handheld showerhead from leaking, you need to clean the inner parts of your diverter gate.

  • Step 1: Turn off your water supply from the main spigot. This prevents flooding.
  • Step 2: Inspect your spout to see how it’s attached to the wall. There are three common styles:
    • A single screw under the spout
    • A threaded pipe that screws onto the wall
    • A pop-in pipe that slides onto the wall and locks in place.
  • Step 3: Remove the spout according to its type:
    • If it’s a screw-on, remove the screw then pull out the spout.
    • If it’s threaded, turn it anticlockwise until it comes off.
    • If it’s a pop-on, use a screwdriver or palette knife to gently pry it off the wall.
  • Step 4: Look inside the spout and use a rasp or sandpaper to scrape off any visible dirt or stains. You can also scrape off the dirt using a paste of vinegar and baking soda. Apply the paste onto the dirty parts of the spout, let it sit for half an hour, then rinse it off.
  • Step 5: Fill a metal dish with vinegar and water. It should be enough to completely cover your spout, right up to its base.
  • Step 6: Put the spout inside your vinegar mixture and leave it for three to four days. Once a day, remove the spout and check it, using a rag or old toothbrush to scrape off loose dirt.
  • Step 7: Once it’s spotless, dry it with a clean rag and add some Teflon tape to the tip.
  • Step 8: Put your spout back onto its copper pipe.
  • Step 9: Reconnect your water supply and run your water to see if you’ve fixed the leak.

At this point, you have a shower spout that looks brand new, so if it’s still not working, you may have to throw it out and buy another shower diverter kit.

Option 4 – Replace the valve gate

Replace the valve gate

If you&#;re still having issues, it&#;s probably time to visit the hardware store. Cheap replacements are easily available and rarely cost more than $ If you just want the gate, it&#;s even cheaper.

  • Step 1: Turn off your water using your main bathroom spigot.
  • Step 2: Cover the drain with duct tape. This prevents small faucet bits and screws from going down the drain and getting lost.
  • Step 3: Remove your shower spout from the wall and carry it to the hardware store.
  • Step 4: Ask for a replacement gate valve that fits your shower model.
  • Step 5: Take your replacement valve home and carefully read the instructions.
  • Step 6: Fix your spout back on the wall. This anchors your spout, making it easier to repair.
  • Step 7: Twist the spout so that it faces upward, but don’t remove it from the wall.
  • Step 8: Pry the plastic prongs apart then pull the white bits out of the spout.
  • Step 9: Remove the metal knob from the top of your spout.
  • Step Slip the new shower diverter knob into the top of the spout.
  • Step Being careful not to drop anything, insert the underside portion of the diverter valve. Start with the spring, followed by the black washer.
  • Step Slip the white plastic peg and snap it into place, holding everything together.
  • Step Turn the spout right side up.
  • Step Reconnect your water, and test the diverter.

This option is cheaper than replacing your entire shower spout, but it’s also more complicated. Many people who try this at home still end up with a leaking diverter, so if you want to do it this way, consider having a plumber do it for you.

Option 5 – Replace the whole spout

Replace The Whole Spout

This seems drastic, but it&#;s easier than you think and is the most effective solution. Shower spouts aren&#;t that expensive. You can get a replacement for as low as $ Decide whether you want to buy the same model you have or replace it with a universal spout.

  • Step 1: Shut off your water supply and remove your spout from the wall.
  • Step 2: Take it to the hardware store and buy a suitable replacement.
  • Step 3: Bring your new spout home and read the instructions.
  • Step 4: Use vinegar and a soft brush to clean any debris off the copper piping on the bathroom wall. This prevents leakage when you put in your new spout.
  • Step 5: Dry the pipe and put some Teflon tape on its edge. This reduces any potential friction and lowers the chances of leakage.
  • Step 6: Fix the spout onto the wall according to its type. You can push it in, screw it in, or hold it in position and insert the under-spout screw.
  • Step 7: Reconnect your water supply and run the tap to see if it’s still leaking.

Consider any variations

When you noticed your shower diverter wasn’t working as it should, you probably ran to Google and YouTube. And as you may have noticed, most online tutorials use tee-valve diverters in their demos. This is partly because tee-valves are more common than the other two types.

But once in a while, you might find yourself dealing with two-valve or three-valve bathroom spouts, especially in older houses. Luckily, they’re just as easy to fix as a tee-valve shower diverter. You can still soak, lubricate, and replace your two-valve or three-valve.

The main difference is in the piping mechanism. When you remove a tee-valve from the wall, you find a single copper pipe. With two-valves and three-valves, you’ll find the corresponding number of copper pipes. If your shower diverter is a two-valve, focus on the temperature dial.

This is because it often doubles as a shower diverter gate. It controls hot and cold, but it also controls up (to the showerhead) or down (to the spout). On the other hand, if the shower has a three-valve diverter, focus on the middle pipe. That’s where the valve is located.

Repair your shower the easy way

It’s annoying when you’re trying to have a shower but your bathtub keeps dripping. Or when you’re filling the tub and the rain shower head keeps wetting your back. With a few basic tools, you can fix it!

  • Soak your faucet in vinegar to get rid of dirt and hard water residue.
  • Spray the diverter knob with cooking spray to lubricate its sticky bits.
  • Replace the shower diverter gate using a store-bought repair kit.
  • Replace the whole spout with a newer model from the hardware store.

Is your shower diverter giving you grief? Tell us all about it in the comments!

Sours: https://www.sunrisespecialty.com/shower-diverter-repair

Diverter wd40 shower

Welcome to Plbg.com
Thank you to all the plumbing professionals who offer their advice and expertise


Over , strictly plumbing related posts

Welcome to Plbg.com and PlumbingForum.com. The best online (strictly) PLUMBING advice, help, dyi, and informational plumbing forum. Questions and discussions about toilets, sinks, faucets, drainage, venting, water heating, showers, pumps, water quality, and other exclusively PLUMBING related issues. Please refrain from asking where to purchase a product, or business, pricing, or legal questions, or for contractor referrals, or any questions not related to plumbing. Keep all posts positive and absolutely no advertising. Our site is completely free, without ads or pop-ups. We do not sell your information. We are made possible by: PlumbingSupply.com 

Author: vaake (VA)

I have a Moen single control tub/shower fixture. The diverter is a rod located below the knob.
The rod has become sticky, both when pushing in, and releasing. There is a squeaking sound when manipulating it.
I have tried WD and moving the rod in and out with pliers but the problem has not gone away.

Thanks for any help.

Post Reply


Author: redwood (CT)

Can you supply the model # or, post a picture of this "Moen" valve with the diverter below the knob?

- - - - - - - - - - - - - - - - - - - -

Since (3 years before Google started) PlumbingSupply.com has been THE best plumbing supplier on the web. Please visit our sponsor [www.PlumbingSupply.com]

Post Reply


Author: vaake (VA)

Here is a photo of the fixture

[ [] ]

Post Reply


Author: dlh (TX)

you have a moentrol valve and you need part #
[www.moen.com]
wd is not good for rubber parts. it makes the rubber hard

- - - - - - -

PLUMBERS "Protecting The Health Of The Nation"

Post Reply


Author: jimmy-o (CA)

WD is the worst thing to put on things with rubber seals, and it does not do much for calcium deposits, either,.

Post Reply


Author: Wheelchair (IL)

Amen, WD disperses water and doesn't lube. Not recommend for faucets either.

Best Wishes

Post Reply



Author: hj (AZ)

It is a Moen valve with a push button diverter in the body. There is only one diverter style so getting the new one is simple.

Post Reply


Author: dlh (TX)

actually hj, there is one for before 6/02 and one for after although the valve bodies are the same

- - - - - - -

PLUMBERS "Protecting The Health Of The Nation"

Post Reply


Author: hj (AZ)

Actually, I have not seen any built in diverter valves made after in this area. They are all the old DialCet versions.

Post Reply


Author: dlh (TX)

you may be right.

all i know is what i read on the parts diagram from delta

- - - - - - -

PLUMBERS "Protecting The Health Of The Nation"

Post Reply


Author: hj (AZ)

I am not saying you are wrong, because I have not had any reason to check on any that new, and all the ones I have come across all use the same one.

Post Reply


Author: LemonPlumber (FL)

dhl you meant moen and it dose come in a longer lenght.check our sponsors link to your part number.Good Luck.

Post Reply






Please note:
  • Inappropriate messages or blatant advertising will be deleted. We cannot be held responsible for bad or inadequate advice.
  • Plbg.com has no control over external content that may be linked to from messages posted here. Please follow external links with caution.
  • Plbg.com is strictly for the exchange of plumbing related advice and NOT to ask about pricing/costs, nor where to find a product (try Google), nor how to operate or promote a business, nor for ethics (law) and the like questions.
  • Plbg.com is also not a place to ask radiant heating (try HeatingHelp.com), electrical or even general construction type questions. We are exclusively for plumbing questions.

Search for plumbing parts on our sponsor's site:


Plbg Advisor ListCommon Plumbing TermsFind A PlumberPlumbing Manufacturers Directorytheplumber.com



Special thanks to our sponsor:
PlumbingSupply.com

to FAQ's - to popular subjects - to plumbing books - to Tankless - to plumbing history - to helping charities - to contact us


Sours: https://www.plbg.com/forum/read.php?1,
How Does a Shower Diverter Work? - The Home Depot

How do you change a tub spout with a diverter?

How do you remove a bathtub diverter? Look for a small setscrew on the underside of the spout next to the wall. Use a hex key to remove the setscrew and pull the spout off the supply pipe. If your tub spout does not have a setscrew, insert a heavy-duty screwdriver into the spout opening and twist it counterclockwise to remove it from the supply pipe.

How much does it cost to replace a tub spout? Install a Bathtub Spout: national average cost

The national average materials cost to install a bathtub spout is $ per spout, with a range between $ to $ The total price for labor and materials per spout is $, coming in between $ to $

How much does it cost to replace a shower diverter? Depending on the severity of the leak, it can cost between $ and $ to fix it.

How do you change a tub spout with a diverter? &#; Related Questions

Where is the shower diverter?

Single-Valve Shower Diverter

This diverter valve, also known as a tee diverter, is located on the end of the tub spout (see photo above). Activating it requires simply pulling up on the diverter, which then sends water to the showerhead.

Can&#;t get my tub spout off?

The first step is to cut through any caulk between the spout and wall. Then grip the spout near the wall with a inch pipe wrench and try again with a little more gusto. Push counter-clockwise, using steady pressure. If that approach doesn&#;t work, you&#;ll need to cut off the spout with a hacksaw.

Do you have to turn off water to change shower diverter?

If you&#;re only working on the diverter, you don&#;t need to turn off the water supply to the faucet. While working, place a cloth over the tub drain to prevent any dropped screws from going down the drain. Some showers use a diverter built into the tub spout activated by lifting a button on the spout.

Can you use wd40 on shower diverter?

WD is great for the bathroom, too

Check out the WD EZ-Reach, perfect for loosening up a sticking tub spout diverter!

How do I know if my shower diverter valve is bad?

To know if your diverter valve is bad, you should check to see if there is not enough water flow, if water flows from both the showerhead and tup fill spigot at the same time, or if there is irregular water flow. A bad diverter valve can also cause excessive or insufficient amounts of hot water.

Can a shower diverter cause a leak?

When a diverter valve is working properly, water only flows out of either the tub spout or the showerhead. However, diverters very often leak significantly, allowing water to flow out of the tub spout even when in shower mode, as shown in Figure 3.

How much does a plumber charge to install a bathtub faucet?

Install a Bathtub Faucet: national average cost

The national average materials cost to install a bathtub faucet is $ per faucet, with a range between $ to $ The total price for labor and materials per faucet is $, coming in between $ to $

How much does a plumber charge to install a faucet?

The cost to install a faucet is between $ and $, with the average being about $ A qualified pro can typically install a new faucet quickly, depending on factors such as the condition of your pipes, location of the sink and the type of faucet. Installing a faucet can revitalize your kitchen or bathroom.

Can I replace the diverter valve?

If you&#;re not sure what a diverter valve is or what it does in your shower, make sure to take a look at our post about everything you need to know about shower diverter valves. That way, if the diverter valve has failed from normal wear and tear, you can get a repair or replacement for that fee.

Is a diverter valve expensive?

You&#;ll come across various models, many of which will provide either heating or hot water, however, a mid-position diverter valve allows you to have heating, hot water and both. They tend to be more expensive but being able to use hot water and keep your radiators warming up is well worth the extra investment.

Why does my tub spout drip?

Drops of water coming out of a tub spout can be normal if it has a diverter or it can be a leaky washer in the shower faucet. If it continues to leak all day, then it&#;s a leaky washer. If it leaks for an hour or so, but then quits, it&#;s water draining down from the shower head and emptying into the tub.

Why does my tub faucet drip?

The annoying and costly non-stop drip from a bathtub faucet is generally caused by the failure of small washers. You don&#;t need a plumber to fix the problem. Turning the faucet handle to the “off” position causes the washers to place pressure against the faucet seat and stop the flow of water.

How do I turn my shower diverter on?

Here&#;s how they work: Three-valve shower diverter: Tubs with separate hot and cold handles may have a three-valve diverter located between them. Turn this third handle clockwise degrees to send hot and cold water to the showerhead. Turn the diverter handle counter-clockwise to restore flow to the tub spout.

How does a three handle shower diverter work?

Three-Valve Shower Diverter

A three-valve shower has three different handles that you turn to open or close the valves. One handle opens the hot water valve, one opens the cold water valve, and the third (generally in the middle of the temperature valves) diverts the water into the spigot or up to the shower head.

How long does a shower diverter last?

The valves are easy to move against pressure. Control the volume from off to full on by leaving them set to the same temperature. The system costs about $30 to replace, but they last for 20 to 30 years.

What type of shower diverter do I have?

Single-valve or T diverter – This is the most common type of diverter. If you have a handle that pulls straight up from the tub faucet, you likely have a T diverter. When you push the handle down, it opens the flow of water to the tub spout.

How do you remove a tub faucet stem?

Wiggle the handle and pull it off. You may need a faucet handle puller if the handle will not come off by hand. Place a socket wrench over the bathtub faucet stem until it covers the hex nut. Turn the wrench counterclockwise to loosen the nut until you can pull the stem free.

How do you remove a tub spout without a set screw?

If there is no set screw, you have a threaded tub spout. You can remove your tub spout by twisting it counter-clockwise to see how your existing spout is threaded, if desired, but it is recommended you leave the spout on if you might need to use the tub before your new spout arrives.

Can you change a faucet without turning off the water?

Although it&#;s not advised, you technically can replace a faucet without turning off your water. To do so, you need to turn on faucets elsewhere in your house to reduce the amount of water pressure going to the faucet you want to replace.

Can you use WD on plumbing?

Liberally apply WD Penetrant spray this into the pipe threading and wait for the fast acting lubricant to soak in and loosen the material. Once loose, remove either end with two pipe wrenches, one for grip and the other for leverage.

Can a bad shower diverter cause low water pressure?

a defective or stuck bathtub spout diverter can cause low shower pressure. This is because your diverter is unable to divert water from your tub spout up to your shower head effectively. To fix this problem, call a plumber to fix/replace your spout diverter.

Sours: https://cementanswers.com/how-do-you-change-a-tub-spout-with-a-diverter/

You will also be interested:

4 Quick Fixes For Annoying Home Problems

FOUR QUICK FIXES FOR ANNOYING HOME PROBLEMS

Want to fix a pesky problem in your home without breaking the bank? Here are four solutions to common, annoying problems in your home that you can tackle yourself in just one weekend. Warning: Success might result in a larger “honey-do” list.

1. Running Toilet

The most common cause of a running toilet is an old rubber flapper – the part that seals out water. To test if this is the issue, put a couple of drops of food coloring in the tank and wait five minutes. If the water in the bowl changes color, it is the flapper. Before changing the flapper, check the flapper chain to make sure it’s not too short (the flapper can’t close) or too long (the chain gets caught). If the chain is fine, you need to purchase a new flapper. Be sure to take the old flapper with you to your local hardware store to make sure you get the right replacement. To learn how to replace a toilet flapper, check out this article from About.com Plumbing.

2. Leaky Faucet

Although leaky faucets may seem like a small issue, it should never be ignored as all those drops of water add up, and if it’s not addressed properly, could turn into a larger problem. All you’ll need to tackle this problem is an adjustable wrench, a flat-head screwdriver, a can of WD-40® Multi-Use Product, and replacement washers and O-rings (available at Lowe’s). Before applying any wrench or screwdriver to your fixture, Popular Mechanics recommends turning off the water supply in your home. After this is done, remove any decorative parts from the handle knobs by prying it off with a flat-head screwdriver. Underneath each knob, there will be a screw that mounts the handle to the stem. Spray a little WD-40 Multi-Use Product to loosen the screw, and unscrew the faucet handle from the stem. Use your wrench to loosen the packing nut and from there you should notice the stem, which should be removed as well. Once this is done, you should remove the washer and O-ring from inside the valve seat and put the replacements inside the seat (click here for a visual on how to do this). From there, carefully reassemble all the parts in order, and slowly and gently turn the knob to test the running water.

3. Water Marks on Wood Furniture

To remove water marks from your wood furniture, cover the water mark with a dry cotton cloth and go over it with a medium-hot iron for several seconds. If that doesn’t work, Better Homes & Gardens recommends lightly wiping the mark with a cloth dampened with denatured alcohol.

4. Broken Tile

To fix a broken tile, remove the grout around the tile with a grout saw, a small tool available at The Home Depot. According to Better Homes & Gardens, if a tile has already started to chip, continue to break it off in little pieces until you can remove the entire damaged tile. If not, make a hole in center with a masonry drill, which will break the tile, and remove the pieces from the center, outward. Glue the new tile in place with superglue and apply fresh grout around the edges.

To learn how to tackle this project, check out This Old House’s step-by-step guide, which includes images for each step.

Sours: https://www.wd40.com/article/four-quick-fixes-for-annoying-home-problems/


37 38 39 40 41